Colt M1861 Navy

Colt M1861 Navy

Colt M1861 Navy
Colt 1861 Navy Revolver, Second Generation
Type Revolver
Place of origin  United States
Service history
In service 1861 to circa 1873
Used by  United States
 Confederate States
Native Americans
Wars American Civil War
American Indian Wars
Production history
Designer Samuel Colt
Manufacturer Colt's Manufacturing Company
Produced 1861-1873
Number built 38,000
Weight 42 oz (1190 g)
Length 13 in (330 mm)
Barrel length 7.5 in (190.5 mm)

Cartridge Paper-wrapped .36 caliber
.38 Short Colt (Conversions)
Caliber 0.36
Action Single action, cap and ball
Muzzle velocity 850 to 1,000 ft/s depending upon load
Feed system 6 round cylinder
Colt Navy Mod 1861, shipped 1863
Colt Navy 1861 Conversion

The Colt Model 1861 Navy cap & ball .36-caliber revolver was a six-shot, single-action percussion weapon produced by Colt's Manufacturing Company from 1861 until 1873. It incorporated the "creeping" or ratchet loading lever and round barrel of the .44-caliber Army Model of 1860 but had a barrel one half inch shorter, at 7.5 inches. Total production was 38,000 revolvers.[1][2]


  • History 1
  • Characteristics 2
  • Colt 1851 Navy Conversions 3
  • See also 4
  • References 5
  • External links 6


Like its forerunner, the Colt 1851 Navy Revolver, it saw widespread use in the American Civil War and on the American Western frontier, though far fewer were produced. It has the same general specification as the earlier model, but with a rounded barrel and somewhat different rammer.[2] While similar in design to the Colt Army Model 1860, the lighter recoil of the 1861 Navy's .36 caliber was preferred by some cavalry soldiers.

During the Civil War its main competitor in England was the Adams self-cocking revolver. The Adams fired a .49 caliber bullet and did not require the shooter to pull the hammer back. Colt's revolver was more popular because Colt mass-produced his weapons while Adams' products were handmade by skilled artisans. In the United States, Colt's main rival was the Remington Model 1858 revolver.


There were few variations of the Model 1861 Navy Colt. Approximately 100 of the first guns made had fluted cylinders with no cylinder scene. Another 100, made between the serial ranges of 11,000 and 14,000 were cut for a shoulder stock — the lower portion of the recoil shield was milled away and a fourth screw for the stock was added to the frame. With the exception of the first fifty or so of this model, all guns had a capping groove. A brass trigger guard and back strap, silver plated, were standard.

The Colt 1861 Navy typically was used with paper cartridges, that is, with a cartridge consisting of nitrated paper, a pre-measured black powder charge, and a bullet that was either a lead round ball or a lead conical bullet. The nitrated paper of the cartridge was completely consumed upon use, and the use of paper cartridges enabled faster re-loading. Alternatively, it was always possible to load with measured powder charges and lead round balls.

Colt 1851 Navy Conversions

After the expiration of the Rollin White Patent (Apr. 3, 1869), a number of Navy 1861 and its forerunner, the Colt 1851 Navy Revolver were converted or newly made to fire .38 rimfire or centerfire cartridges, the Colt Model 1861 Richards- Mason Conversion by the Colt factory.

See also


  1. ^ R.L. Wilson, Colt, an American Legend
  2. ^ a b Hogg, Ian V. (1987). Weapons of the Civil War.  

External links

  • The Colt Revolver in the American West—Presentation Model 1861 Navy
  • The Colt Revolver in the American West—Cased Presentation Model 1861 Navy
  • Smithsonian Article on the M1861 Navy
  • Shooting Characteristics of the M1861 Navy