Arcminute
A minute of arc, arcminute, or minute arc (MOA), is a unit of angular measurement equal to one sixtieth (^{1}⁄_{60}) of one degree. In turn, a second of arc or arcsecond is one sixtieth (^{1}⁄_{60}) of one arcminute. Since one degree is defined as one three hundred and sixtieth (^{1}⁄_{360}) of a rotation, one minute of arc is ^{1}⁄_{21,600} of a rotation, which also equals ^{π}⁄_{10,800} radians. It is used in those fields which require a unit for the expression of small angles, such as astronomy, optometry, ophthalmology, optics, navigation and marksmanship.
The number of square arcminutes in a complete sphere is
 $4\; \backslash pi\; \backslash left(\backslash frac\{1\}\{\backslash pi\}10\backslash ,800\backslash right)^2\; =\; \backslash frac\{1\}\{\backslash pi\}466\backslash ,560\backslash ,000,$
or approximately 148,510,660.498 square arcminutes.
The arcsecond is ^{1}⁄_{3,600} of a degree, or ^{1}⁄_{1,296,000} of a circle, or ^{π}⁄_{648,000} radians (which is approximately ^{1}⁄_{206,265} radian).
To express even smaller angles, standard SI prefixes can be employed; in particular, the milliarcsecond, abbreviated mas, is used in astronomy.
Contents
Symbols and abbreviations
The standard symbol for marking the arcminute is the prime (′) (U+2032), though a single quote (') (U+0027) is commonly used where only ASCII characters are permitted. One arcminute is thus written 1′. It is also abbreviated as arcmin or amin or, less commonly, the prime with a circumflex over it ($\backslash hat\{\text{'}\}$).
The standard symbol for the arcsecond is the double prime (″) (U+2033), though a double quote (") (U+0022) is commonly used where only ASCII characters are permitted. One arcsecond is thus written 1″. It is also abbreviated as arcsec or asec.
Unit  Value  Symbol  Abbreviations  In radians (approx.) 

Degree  ^{1}⁄_{360} circle  °  deg  17.4532925 mrad 
Arcminute  ^{1}⁄_{60} degree  ′ (prime)  arcmin, amin, am, $\backslash hat\{\text{'}\}$, MOA  290.8882087 µrad 
Arcsecond  ^{1}⁄_{60} arcminute  ″ (double prime)  arcsec, asec, as  4.8481368 µrad 
Milliarcsecond  ^{1}⁄_{1,000} arcsecond  mas  4.8481368 nrad  
Microarcsecond  10^{−6} arcsecond  μas  4.8481368 prad 
In celestial navigation, seconds of arc are rarely used in calculations, the preference usually being for degrees, minutes and decimals of a minute, written for example as 42° 25′.32 or 42° 25′.322.^{[1]}^{[2]} This notation has been carried over into marine GPS receivers, which normally display latitude and longitude in the latter format by default.^{[3]}
Uses
Firearms
The arcminute is commonly found in the firearms industry and literature, particularly concerning the accuracy of rifles, though the industry refers to it as minute of angle. It is especially popular with shooters familiar with the Imperial measurement system because 1 MOA subtends approximately one inch at 100 yards, a traditional distance on target ranges. Since most modern rifle scopes are adjustable in half (^{1}⁄_{2}), quarter (^{1}⁄_{4}), or eighth (^{1}⁄_{8}) MOA increments, also known as clicks, this makes zeroing and adjustments much easier. For example, if the point of impact is 3" high and 1.5" left of the point of aim at 100 yards, the scope needs to be adjusted 3 MOA down, and 1.5 MOA right. Such adjustments are trivial when the scope's adjustment dials have an MOA scale printed on them, and even figuring the right number of clicks is relatively easy on scopes that click in fractions of MOA.
One thing to be aware of is that some scopes, including some higherend models, are calibrated such that an adjustment of 1 MOA corresponds to exactly 1 inch, rather than 1.047". This is commonly known as the Shooter's MOA (SMOA) or Inches Per Hundred Yards (IPHY). While the difference between one true MOA and one SMOA is less than half of an inch even at 1000 yards,^{[4]} this error compounds significantly on longer range shots that may require adjustment upwards of 2030 MOA to compensate for the bullet drop. If a shot requires an adjustment of 20 MOA or more, the difference between true MOA and SMOA will add up to 1 inch or more. In competitive target shooting, this might mean the difference between a hit and a miss.
The physical group size equivalent to m minutes of arc can be calculated as follows: group size = tan(^{m}⁄_{60}) × distance. In the example previously given, for 1 minute of arc, and substituting 3,600 inches for 100 yards, 3,600 tan(^{1}⁄_{60}) = 1.047 inches. In metric units 1 MOA at 100 meters = 2.908 centimeters.
Sometimes, a precision firearm's accuracy will be measured in MOA. This simply means that under ideal conditions i.e. no wind, matchgrade ammo, clean barrel, and a vise or a benchrest used to eliminate shooter error, the gun is capable of producing a group of shots whose center points (centertocenter) fit into a circle, the average diameter of circles in several groups can be subtended by that amount of arc. For example, a 1 MOA rifle should be capable, under ideal conditions, of shooting an average 1inch groups at 100 yards. Most higherend rifles are warrantied by their manufacturer to shoot under a given MOA threshold (typically 1 MOA or better) with specific ammunition and no error on the shooter's part. For example, Remington's M24 Sniper Weapon System is required to shoot 0.8 MOA or better, or be rejected.
Rifle manufacturers and gun magazines often refer to this capability as subMOA, meaning it shoots under 1 MOA. This means that a single group of 3 to 5 shots at 100 yards, or the average of several groups, will measure less than 1 MOA between the two furthest shots in the group, i.e. all shots fall within 1 MOA. If larger samples are taken (i.e., more shots per group) then group size typically increases, however this will ultimately average out. If a rifle was truly a 1 MOA rifle, it would be just as likely that two consecutive shots land exactly on top of each other as that they land 1 MOA apart. For 5 shot groups, based on 95% confidence a rifle that normally shoots 1 MOA can be expected to shoot groups between 0.58 MOA and 1.47 MOA, although the majority of these groups will be under 1 MOA. What this means in practice is if a rifle that shoots 1" groups on average at 100 yards shoots a group measuring .7" followed by a group that is 1.3" this is not statistically abnormal.^{[5]}^{[6]}
The Metric System counterpart of the MOA is the MilRad, being equal to one 1000th of the target range, laid out on a circle that has the observer as centre and the target range as radius. The number of MilRads on a full such circle therefore always is equal to 2 x π x 1000, regardless the target range. Therefore 1 MOA = 0.2908 MilRad. This means that an object which spans 1 MilRad on the reticle is at a range that is in meters equal to the object's size in millimeters (e.g. an object of 100 mm @ 1 Milrad is 100 meters away). So there is no conversion factor required, contrary to the MOA system. The markings on a reticle that mark MilRads are called MilDots. Such reticle is called a MilDot Reticle.
Cartography
Minutes of arc (and its subunit, seconds of arc or SOA—equal to a sixtieth of a MOA) are also used in cartography and navigation. At sea level one minute of arc along the equator or a meridian equals approximately one Nautical mile (1.852 km or 1.151 mi). A second of arc, one sixtieth of this amount, is about 30 meters or roughly 100 feet. The exact distance varies along meridians because the shape of the Earth is slightly oblate.
Positions are traditionally given using degrees, minutes, and seconds of arcs for latitude, the arc north or south of the equator, and for longitude, the arc east or west of the Prime Meridian. Any position on or above the Earth's reference ellipsoid can be precisely given with this method. However, because of the somewhat clumsy base60 nature of minutes and seconds, positions are frequently expressed in fractional degrees only, expressed in decimal form to an equal amount of precision. Degrees given to three decimal places (^{1}⁄_{1,000} of a degree) have about ^{1}⁄_{4} the precision of degreesminutesseconds (^{1}⁄_{3,600} of a degree) and specify locations within about 120 meters or 400 feet.
Property cadastral surveying
Related to cartography, property boundary surveying using the metes and bounds system relies on fractions of a degree to describe property lines' angles in reference to cardinal directions. A boundary "mete" is described with a beginning reference point, the cardinal direction North or South followed by an angle less than 90 degrees and a second cardinal direction, and a linear distance. The boundary runs the specified linear distance from the beginning point, the direction of the distance being determined by rotating the first cardinal direction the specified angle toward the second cardinal direction. For example, North 65° 39′ 18″ West 85.69 feet would describe a line running from the starting point 85.69 feet in a direction 65° 39′ 18″ (or 65.655°) away from north toward the west.
Astronomy
The arcminute and arcsecond are also used in astronomy. Degrees (and therefore arcminutes) are used to measure declination, or angular distance north or south of the celestial equator. The arcsecond is also often used to describe parallax, due to very small parallax angles for stellar parallax, and tiny angular diameters (e.g., Venus varies between 10′′ and 60′′). The parallax, proper motion and angular diameter of a star may also be written in milliarcseconds (mas), or thousandths of an arcsecond. The parsec gets its name from "parallax second", for those arcseconds.
The ESA astrometric space probe Gaia is hoped to measure star positions to 20 microarcseconds (µas) when it begins producing catalog positions sometime after 2016. There are about 1.3 quadrillion µas in a circle. As seen from Earth, one µas is about the size of a period at the end of a sentence in the Apollo mission manuals left on the moon. Currently the best catalog positions of stars actually measured are in terms of milliarcseconds, by the U.S. Naval Observatory. A milliarcsecond is about the size of a dime atop the Eiffel Tower as seen from New York City.
Apart from the Sun, the star with the largest angular diameter from Earth is R Doradus, a red supergiant with a diameter of 0.05 arcsecond.^{[7]} Because of the effects of atmospheric seeing, groundbased telescopes will smear the image of a star to an angular diameter of about 0.5 arcsecond; in poor seeing conditions this increases to 1.5 arcseconds or even more. The dwarf planet Pluto has proven difficult to resolve because its angular diameter is about 0.1 arcsecond.^{[8]} This is roughly equivalent to a (40 mm) pingpong ball viewed at a distance of 50 miles (80 km).
Space telescopes are not affected by the Earth's atmosphere but are diffraction limited. For example, the Hubble space telescope can reach an angular size of stars down to about 0.1″. Techniques exist for improving seeing on the ground. Adaptive optics, for example, can produce images around 0.05 arcsecond on a 10 m class telescope.
Human vision
In humans, 20/20 vision is the ability to resolve a spatial pattern separated by a visual angle of one minute of arc. A 20/20 letter subtends 5 minutes of arc total.
Materials
The deviation from parallelism between two surfaces, for instance in optical engineering, is usually measured in arcminutes or arcseconds.
Notes and references
External links
 MOA: Rifle Reticles by Robert Simeone
