Specific impulse (usually abbreviated I_{sp}) is a measure of the efficiency of rocket and jet engines. It represents the force with respect to the amount of propellant used per unit time.^{[1]} If the "amount" of propellant is given in terms of mass (such as in kilograms), then specific impulse has units of velocity. If it is given in terms of weight (such as in kiloponds or newtons), then specific impulse has units of time (seconds). The conversion constant between these two versions is thus essentially "gravity" (more specifically g_{0}).^{[2]} The higher the specific impulse, the lower the propellant flow rate required for a given thrust, and in the case of a rocket the less propellant needed for a given deltav per the Tsiolkovsky rocket equation.
Specific impulse is a useful value to compare engines, much like miles per gallon or liters per 100 kilometers is used for cars.^{[3]} A propulsion method and system with a higher specific impulse is more propellantefficient.^{[1]}^{[4]} While the unit of seconds can seem confusing to laypeople, it is fairly simple to understand as "hovertime": how long a rocket can "hover" before running out of fuel, given the weight of that propellant/fuel. Of course, the weight of the rocket has to be taken out of consideration and so does the reduction in fuel weight as it's expended; the basic idea is "how long can any given amount of x hold itself up". Obviously that must mean "...against Earth's gravity", which means nothing in nonEarth conditions; hence I_{sp} being given in velocity when propellant is measured in mass rather than weight, and the question becomes "how fast can any given amount of x accelerate itself to?".
Note that I_{sp} describes efficiency in terms of amount of propellant, not the engine (or engine/propellant design/combination). Higher I_{sp} means less propellant needed to impart a given momentum, but it says nothing about the overall system's ability to supply needed thrust, especially with respect to time. Some systems with very high I_{sp} (cf. ion thrusters) may have relatively very heavy/massive power generators, and/or produce thrust over a long period; thus, while "efficient" in terms of propellant mass carried, they may actually be quite poor at delivering high thrust quickly vs. "less efficient" engine/propellant designs.
Another number that measures the same thing, usually used for air breathing jet engines, is specific fuel consumption. Specific fuel consumption is inversely proportional to specific impulse and effective exhaust velocity. The actual exhaust velocity is the average speed of the exhaust jet as it leaves the vehicle. The effective exhaust velocity is the exhaust velocity that the propellant would need to produce the same thrust. The two are identical for an ideal rocket working in vacuum, but are radically different for an airbreathing jet engine that obtains extra thrust by accelerating air. Specific impulse and effective exhaust velocity are proportional.
Contents
General considerations
The amount of propellant is normally measured either in units of mass or weight. If mass is used, specific impulse is an impulse per unit mass, which dimensional analysis shows to be a unit of speed, and so specific impulses are often measured in meters per second and are often termed effective exhaust velocity. However, if propellant weight is used instead, an impulse divided by a force (weight) turns out to be a unit of time, and so specific impulses are measured in seconds. These two formulations are both widely used and differ from each other by a factor of g_{0}, the dimensioned constant of gravitational acceleration at the surface of the Earth.
Note that the rate of gain of momentum of a rocket (including fuel) per unit time is equal to the thrust.
The higher the specific impulse, the less propellant is needed to produce a given thrust during a given time. In this regard a propellant is more efficient if the specific impulse is higher. This should not be confused with energy efficiency, which can even decrease as specific impulse increases, since propulsion systems that give high specific impulse require high energy to do so.^{[5]}
In addition it is important that thrust and specific impulse not be confused with each other. The specific impulse is a measure of the impulse per unit of propellant that is expended, while thrust is a measure of the momentary or peak force supplied by a particular engine. In many cases, propulsion systems with very high specific impulses—some ion thrusters reach 10,000 seconds—produce low thrusts.^{[6]}
When calculating specific impulse, only propellant that is carried with the vehicle before use is counted. For a chemical rocket the propellant mass therefore would include both fuel and oxidizer; for airbreathing engines only the mass of the fuel is counted, not the mass of air passing through the engine.
Units
Specific impulse (by weight)  Specific impulse (by mass)  Effective exhaust velocity  Specific fuel consumption  

SI  =X seconds  =(9.8066 X) N·s/kg  =(9.8066 X) m/s  =(101,972/X) g/(kN·s) 
Imperial units  =X seconds  =X lbf·s/lb  =(32.16 X) ft/s  =(3,600/X) lb/(lbf·h) 
By far the most common unit used for specific impulse today is the second, and this is used both in the SI world as well as where Imperial units are used. Its chief advantages are that its units and numerical value are identical everywhere, and essentially everyone understands it. Nearly all manufacturers quote their engine performance in seconds, and it is also useful for specifying aircraft engine performance.^{[7]}
The effective exhaust velocity in units of m/s is also in reasonably common usage. For rocket engines it is reasonably intuitive, although for many rocket engines the effective exhaust speed is considerably different from the actual exhaust speed due to, for example, fuel and oxidizer that is dumped overboard after powering turbopumps. For airbreathing engines the effective exhaust velocity is not physically meaningful, although it can be used for comparison purposes nevertheless.^{[8]}
The values expressed in N·s/kg are not uncommonly seen and are numerically equal to the effective exhaust velocity in m/s (from Newton's second law and the definition of the newton.)
Another equivalent unit is specific fuel consumption. This has units of g/(kN·s) or lb/(lbf·h) and is inversely proportional to specific impulse. Specific fuel consumption is used extensively for describing the performance of airbreathing jet engines.^{[9]}
Specific impulse in seconds
General definition
For all vehicles specific impulse (impulse per unit weightonEarth of propellant) in seconds can be defined by the following equation:^{[3]}
 F_\text{thrust} = I_\text{sp} \cdot \dot m \cdot g_0,
where:
 F_\text{thrust} is the thrust obtained from the engine, in newtons (or poundals),
 I_\text{sp} is the specific impulse measured in seconds,
 \dot m is the mass flow rate in kg/s (lb/s), which is negative the timerate of change of the vehicle's mass (since propellant is being expelled),
 g_0 is the acceleration at the Earth's surface, in m/s^{2} (or ft/s^{2}).
(When working with English units, it is conventional to divide both sides of the equation by g_{0} so that the lefthand side of the equation has units of lbs rather than expressing it in poundals.)
This I_{sp} expressed in seconds is somewhat physically meaningful—if an engine's thrust could be adjusted to equal the initial weight of its propellant (measured at one standard gravity), then I_{sp} is the duration the propellant would last.
The advantage of this formulation is that it may be used for rockets, where all the reaction mass is carried on board, as well as aeroplanes, where most of the reaction mass is taken from the atmosphere. In addition, it gives a result that is independent of units used (provided the unit of time used is the second).
Rocketry
In rocketry, where the only reaction mass is the propellant, an equivalent way of calculating the specific impulse in seconds is also frequently used. In this sense, specific impulse is defined as the thrust integrated over time per unit weightonEarth of the propellant:^{[2]}
 I_{\rm sp}=\frac{v_\text{e}}{g_0},
where
 I_{sp} is the specific impulse measured in seconds,
 v_\text{e} is the average exhaust speed along the axis of the engine (in ft/s or m/s),
 g_{0} is the acceleration at the Earth's surface (in ft/s^{2} or m/s^{2}).
In rockets, due to atmospheric effects, the specific impulse varies with altitude, reaching a maximum in a vacuum. This is because the exhaust velocity isn't simply a function of the chamber pressure, but is a function of the difference between the interior and exterior of the combustion chamber. It is therefore important to note whether the specific impulse refers to operation in a vacuum or at sea level. Values are usually indicated with or near the units of specific impulse (e.g. "sl", "vac").
Specific impulse as a speed (effective exhaust velocity)
Because of the geocentric factor of g_{0} in the equation for specific impulse, many prefer to define the specific impulse of a rocket (in particular) in terms of thrust per unit mass flow of propellant (instead of per unit weight flow). This is an equally valid (and in some ways somewhat simpler) way of defining the effectiveness of a rocket propellant. For a rocket, the specific impulse defined in this way is simply the effective exhaust velocity relative to the rocket, v_{e}. The two definitions of specific impulse are proportional to one another, and related to each other by:
 v_\text{e} = g_0 I_\text{sp},
where
 I_\text{sp} is the specific impulse in seconds,
 v_\text{e} is the specific impulse measured in m/s, which is the same as the effective exhaust velocity measured in m/s (or ft/s if g is in ft/s^{2}),
 g_0 is the acceleration due to gravity at the Earth's surface, 9.81 m/s^{2} (in Imperial units 32.2 ft/s^{2}).
This equation is also valid for airbreathing jet engines, but is rarely used in practice.
(Note that different symbols are sometimes used; for example, c is also sometimes seen for exhaust velocity. While the symbol I_\text{sp} might logically be used for specific impulse in units of N·s/kg; to avoid confusion, it is desirable to reserve this for specific impulse measured in seconds.)
It is related to the thrust, or forward force on the rocket by the equation:^{[10]}
 F_\text{thrust} = v_\text{e} \cdot \dot m,
where \dot m is the propellant mass flow rate, which is the rate of decrease of the vehicle's mass.
A rocket must carry all its fuel with it, so the mass of the unburned fuel must be accelerated along with the rocket itself. Minimizing the mass of fuel required to achieve a given push is crucial to building effective rockets. The Tsiolkovsky rocket equation shows that for a rocket with a given empty mass and a given amount of fuel, the total change in velocity it can accomplish is proportional to the effective exhaust velocity.
A spacecraft without propulsion follows an orbit determined by the gravitational field. Deviations from the corresponding velocity pattern (these are called Δv) are achieved by sending exhaust mass in the direction opposite to that of the desired velocity change.
Actual exhaust speed versus effective exhaust speed
Note that effective exhaust velocity and actual exhaust velocity can be significantly different, for example when a rocket is run within the atmosphere, atmospheric pressure on the outside of the engine causes a retarding force that reduces the specific impulse, and the effective exhaust velocity goes down, whereas the actual exhaust velocity is largely unaffected. Also, sometimes rocket engines have a separate nozzle for the turbopump turbine gas, and then calculating the effective exhaust velocity requires averaging the two mass flows as well as accounting for any atmospheric pressure.
For airbreathing jet engines, particularly turbofans, the actual exhaust velocity and the effective exhaust velocity are different by orders of magnitude. This is because a good deal of additional momentum is obtained by using air as reaction mass. This allows a better match between the airspeed and the exhaust speed, which saves energy/propellant and enormously increases the effective exhaust velocity while reducing the actual exhaust velocity.
Energy efficiency
Rockets
For rockets and rocketlike engines such as iondrives a higher I_{sp} implies lower energy efficiency: the power needed to run the engine is simply:
 \frac {dm} {dt} \frac { v_e^2 } {2}
where v_{e} is the actual jet velocity.
whereas from momentum considerations the thrust generated is:
 \frac {dm} {dt} v_e
Dividing the power by the thrust to obtain the specific power requirements we get:
 \frac {v_e} {2}
Hence the power needed is proportional to the exhaust velocity, with higher velocities needing higher power for the same thrust, causing less energy efficiency per unit thrust.
However, the total energy for a mission depends on total propellant use, as well as how much energy is needed per unit of propellant. For low exhaust velocity with respect to the mission deltav, enormous amounts of reaction mass is needed. In fact a very low exhaust velocity is not energy efficient at all for this reason; but it turns out that neither are very high exhaust velocities.
Theoretically, for a given deltav, in space, among all fixed values for the exhaust speed the value v_\text{e}=0.6275 \Delta v is the most energy efficient for a specified (fixed) final mass, see energy in spacecraft propulsion.
However, a variable exhaust speed can be more energy efficient still. For example, if a rocket is accelerated from some positive initial speed using an exhaust speed equal to the speed of the rocket no energy is lost as kinetic energy of reaction mass, since it becomes stationary.^{[11]} (Theoretically, by making this initial speed low and using another method of obtaining this small speed, the energy efficiency approaches 100%, but requires a large initial mass.) In this case the rocket keeps the same momentum, so its speed is inversely proportional to its remaining mass. During such a flight the kinetic energy of the rocket is proportional to its speed and, correspondingly, inversely proportional to its remaining mass. The power needed per unit acceleration is constant throughout the flight; the reaction mass to be expelled per unit time to produce a given acceleration is proportional to the square of the rocket's remaining mass.
Also it is advantageous to expel reaction mass at a location where the gravity potential is low, see Oberth effect.
Air breathing
Airbreathing engines such as turbojets increase the momentum generated from their propellant by using it to power the acceleration of inert air rearwards. It turns out that the amount of energy needed to generate a particular amount of thrust is inversely proportional to the amount of air propelled rearwards, thus increasing the mass of air (as with a turbofan) both improves energy efficiency as well as I_{sp}.
Examples
Engine 
Effective exhaust velocity (m/s, kg·m/(s·kg)) 
Specific impulse (s) 
Energy per kg of exhaust (MJ/kg) 

Turbofan jet engine (actual V is ~300 m/s) 
29,000  3,000  ~0.05 
Solid rocket 
2,500  250  3 
Bipropellant liquid rocket 
4,400  450  9.7 
Ion thruster  29,000  3,000  430 
Dualstage 4grid electrostatic ion thruster^{[12]}  210,000  21,400  22,500 
VASIMR^{[13]}^{[14]}^{[15]}  30,000–120,000  3,000–12,000  1,400 
 For a more complete list see: Spacecraft propulsion#Table of methods
An example of a specific impulse measured in time is 453 seconds, which is equivalent to an effective exhaust velocity of 4,440 m/s, for the Space Shuttle Main Engines when operating in a vacuum.^{[16]} An airbreathing jet engine typically has a much larger specific impulse than a rocket; for example a turbofan jet engine may have a specific impulse of 6,000 seconds or more at sea level whereas a rocket would be around 200–400 seconds.^{[17]}
An airbreathing engine is thus much more propellant efficient than a rocket engine, because the actual exhaust speed is much lower, the air provides an oxidizer, and air is used as reaction mass. Since the physical exhaust velocity is lower, the kinetic energy the exhaust carries away is lower and thus the jet engine uses far less energy to generate thrust (at subsonic speeds).^{[18]} While the actual exhaust velocity is lower for airbreathing engines, the effective exhaust velocity is very high for jet engines. This is because the effective exhaust velocity calculation essentially assumes that the propellant is providing all the thrust, and hence is not physically meaningful for airbreathing engines; nevertheless, it is useful for comparison with other types of engines.^{[19]}
The highest specific impulse for a chemical propellant ever testfired in a rocket engine was 542 seconds (5,320 m/s) with a tripropellant of lithium, fluorine, and hydrogen. However, this combination is impractical; see rocket fuel.^{[20]}
Nuclear thermal rocket engines differ from conventional rocket engines in that thrust is created strictly through thermodynamic phenomena, with no chemical reaction.^{[21]} The nuclear rocket typically operates by passing hydrogen gas through a superheated nuclear core. Testing in the 1960s yielded specific impulses of about 850 seconds (8,340 m/s), about twice that of the Space Shuttle engines.
A variety of other nonrocket propulsion methods, such as ion thrusters, give much higher specific impulse but with much lower thrust; for example the Hall effect thruster on the SMART1 satellite has a specific impulse of 1,640 s (16,100 m/s) but a maximum thrust of only 68 millinewtons.^{[22]} The Variable specific impulse magnetoplasma rocket (VASIMR) engine currently in development will theoretically yield 20,000−300,000 m/s, and a maximum thrust of 5.7 newtons. ^{[23]}
Larger engines
Here are some example numbers for larger jet and rocket engines:Engine type  Scenario  SFC in lb/(lbf·h)  SFC in g/(kN·s)  Specific impulse (s)  Effective exhaust velocity (m/s) 

NK33 rocket engine  Vacuum  10.9  309  331^{[24]}  3,240 
SSME rocket engine  Space shuttle vacuum  7.95  225  453^{[25]}  4,423 
Ramjet  Mach 1  4.5  127  800  7,877 
J58 turbojet  SR71 at Mach 3.2 (Wet)  1.9  53.8  1,900  18,587 
RollsRoyce/Snecma Olympus 593  Concorde Mach 2 cruise (Dry)  1.195^{[26]}  33.8  3,012  29,553 
CF680C2B1F turbofan  Boeing 747400 cruise  0.605^{[26]}  17.1  5,950  58,400 
General Electric CF6 turbofan  Sea level  0.307^{[26]}  8.696  11,700  115,000 
Model rocketry
Specific impulse is also used to measure performance in model rocket motors. Following are some of Estes' claimed values for specific impulses for several of their rocket motors:^{[27]} Estes Industries is a large, wellknown American seller of model rocket components. The specific impulse for these model rocket motors is much lower than for many other rocket motors because the manufacturer uses black powder propellant and emphasizes safety rather than maximum performance. The burn rate and hence chamber pressure and maximum thrust of model rocket motors is also tightly controlled.Engine  Total impulse (Ns)  Fuel weight (N)  Specific impulse (s) 

Estes A103T  2.5  0.0370  67.49 
Estes A83  2.5  0.0306  81.76 
Estes B42  5.0  0.0816  61.25 
Estes B64  5.0  0.0612  81.76 
Estes C63  10  0.1223  81.76 
Estes C115  10  0.1078  92.76 
Estes D123  20  0.2443  81.86 
Estes E96  30  0.3508  85.51 
See also
 Jet engine
 Impulse
 Tsiolkovsky rocket equation
 Systemspecific impulse
 Specific energy
 Thrust specific fuel consumption  fuel consumption per unit thrust
 Specific thrust  thrust per unit of air for a duct engine
 Heating value
 Energy density
 Deltav (physics)
 Rocket propellant
 Liquid rocket propellants
References
 ^ ^{a} ^{b} "What is specific impulse?". Qualitative Reasoning Group. Retrieved 22 December 2009.
 ^ ^{a} ^{b} Benson, Tom (11 July 2008). "Specific impulse". NASA. Retrieved 22 December 2009.
 ^ ^{a} ^{b} Rocket Propulsion Elements, 7th Edition by George P. Sutton, Oscar Biblarz

^ Hutchinson, Lee (14 April 2013). "New F1B rocket engine upgrades Apolloera design with 1.8M lbs of thrust". ARS technica. Retrieved 15 April 2013.
The measure of a rocket's fuel efficiency is called its specific impulse (abbreviated as "ISP"—or more properly Isp). ... 'Mass specific impulse...describes the thrustproducing efficiency of a chemical reaction and it is most easily thought of as the amount of thrust force produced by each pound (mass) of fuel and oxidizer propellant burned in a unit of time. It is kind of like a measure of miles per gallon (mpg) for rockets.'
 ^ http://www.geoffreylandis.com/laser_ion_pres.htp
 ^ "Mission Overview". exploreMarsnow. Retrieved 23 December 2009.
 ^ http://www.grc.nasa.gov/WWW/k12/airplane/specimp.html
 ^ http://www.qrg.northwestern.edu/projects/vss/docs/propulsion/3whatisspecificimpulse.html
 ^ http://www.grc.nasa.gov/WWW/k12/airplane/sfc.html
 ^ Aerospace Propulsion Systems By Thomas A. Ward
 ^ Note that this limits the speed of the rocket to the maximum exhaust speed.
 ^ http://www.esa.int/esaCP/SEMOSTG23IE_index_0.html
 ^ http://vasimr.net/TimSTAIF2005.pdf
 ^ http://www.adastrarocket.com/AIAA20106772196_small.pdf
 ^ http://spacefellowship.com/news/art24083/vasimrvx200meetsfullpowerefficiencymilestone.html
 ^ http://www.astronautix.com/engines/ssme.htm
 ^ http://web.mit.edu/16.unified/www/SPRING/propulsion/notes/node85.html
 ^ http://www.dunnspace.com/isp.htm
 ^ http://www.britannica.com/EBchecked/topic/198045/effectiveexhaustvelocity
 ^ ARBIT, H. A., CLAPP, S. D., DICKERSON, R. A., NAGAI, C. K., Combustion characteristics of the fluorinelithium/hydrogen tripropellant combination. AMERICAN INST OF AERONAUTICS AND ASTRONAUTICS, PROPULSION JOINT SPECIALIST CONFERENCE, 4TH, CLEVELAND, OHIO, June 10–14, 1968.
 ^ http://trajectory.grc.nasa.gov/projects/ntp/index.shtml
 ^ http://www.mendeley.com/research/characterizationofahighspecificimpulsexenonhalleffectthruster/
 ^ http://www.adastrarocket.com/AdAstra%20Release%2023Nov2010final.pdf
 ^ Astronautix NK33
 ^ Astronautix SSME
 ^ ^{a} ^{b} ^{c} "Data on Large Turbofan Engines". Aircraft Aerodynamics and Design Group. Stanford University. Retrieved 22 December 2009.
 ^ Estes 2011 Catalog www.acsupplyco.com/estes/estes_cat_2011.pdf
External links
 RPA  Design Tool for Liquid Rocket Engine Analysis
 List of Specific Impulses of various rocket fuels