Slab track

A railroad tie/railway tie/crosstie (North America), or railway sleeper (Europe, Australia & Asia) is a rectangular support for the rails in railroad tracks. Generally laid perpendicular to the rails, ties transfer loads to the track ballast and subgrade, hold the rails upright, and keep them spaced to the correct gauge.

Railroad ties were traditionally made of wood, but pre-stressed concrete is now widely used especially in Europe and Asia. Steel ties are common on secondary lines in the UK; plastic composite ties are also employed, although far less than wood or concrete. As of January 2008, the approximate market share in North America for traditional and wood ties was 91.5%, the remainder being concrete, steel, azobé (red ironwood) and plastic composite.[1]

Coarse aggregate is the standard material for track ballast, which provides drainage and resilience. On lines with lower speeds and axle-weights, sand, gravel, and even coal ash from the fires of steam locomotives have been used.

Up to 3000 ties are used per mile of railroad track in the USA, 2640 per mile (30 per 60 ft rail) on main lines in the UK. Rails in the USA may be fastened to the tie by a railroad spike; iron/steel baseplates screwed to the tie and secured to the rail by a proprietary fastening system such as a Vossloh or Pandrol are commonly used in Europe.


Stone block

The type of tie used on the predecessors of the first true railway (Liverpool and Manchester Railway) consisted of a pair of stone blocks laid into the ground, with the chairs holding the rails fixed to those blocks. One advantage of this method of construction was that it allowed horses to tread the middle path without the risk of tripping. In railway use with ever heavier locomotives, it was found that it was hard to maintain the correct gauge. The stone blocks were in any case unsuitable on soft ground, such as Chat Moss, where timber ties had to be used.

Bi-block (see below) with a tie rod, are somewhat similar.


A variety of softwood and hardwoods timbers are used as ties, oak, jarrah and karri being popular hardwoods, although increasingly difficult to obtain, especially from sustainable sources.[2] Some lines use softwoods, including Douglas fir; while they have the advantage of accepting treatment more readily, they are more susceptible to wear but are cheaper, lighter (and therefore easier to handle) and more readily available.[2] Softwood is treated, historically using creosote, but nowadays with other less-toxic preservatives to improve resistance to insect infestation and rot. New boron-based wood preserving technology is being employed by major US railroads in a dual treatment process in order to extend the life of wood ties in wet areas.[3] Some timbers (such as sal, mora, jarrah or azobé) are durable enough that they can be used untreated.[4]

Problems with wood ties include rot, splitting, insect infestation, plate-cutting, also known as chair shuffle in the UK (abrasive damage to the tie caused by lateral motion of the tie plate) and spike-pull (where the spike is gradually loosened from the tie). For more information on wood ties the Railway Tie Association maintains a comprehensive website devoted to wood tie research and statistics.


Main article: Concrete sleeper

Concrete ties are cheaper and easier to obtain than timber and better able to carry higher axle-weights and sustain higher speeds. Their greater weight ensures improved retention of track geometry especially when installed with continuous-welded rail. Concrete ties have a longer service life and require less maintenance than timber due to their greater weight which helps them remain in the correct position longer. Concrete ties need to be installed on a well-prepared subgrade with an adequate depth on free-draining ballast to perform well.

On the highest categories of line in the UK (those with the highest speeds and tonnages) pre-stressed concrete ties are the only ones permitted by Network Rail standards.

Most European railways also now use concrete bearers in switches and crossing layouts due to the longer life and lower cost of concrete bearers compared to timber, which is increasingly difficult and expensive to source in sufficient quantities and quality.


Steel ties are formed from pressed steel and are trough-shaped in section. The ends of the tie are shaped to form a "spade" which increases the lateral resistance of the tie. Housings to accommodate the fastening system are welded to the upper surface of the tie. Steel ties are now in widespread use on secondary or lower-speed lines in the UK where they have been found to be economical to install due their ability to be installed on the existing ballast bed. Steel ties are lighter in weight than concrete and able to stack in compact bundles unlike timber. Steel ties can be installed onto the existing ballast, unlike concrete ties which require a full depth of new ballast. Steel ties are 100% recyclable and require up to 60% less ballast than concrete ties and up to 45% less than wood ties.

Historically, steel ties have suffered from poor design and increased traffic loads over their normally long service life. These aged and often obsolete designs limited load and speed capacity but can still be found in many locations globally and performing adequately despite decades of service. There are great numbers of steel ties with over 50 years of service and in some cases they can and have been rehabilitated and continue to perform well. Steel ties were also used in specialty situations, such as the Hejaz Railway in the Arabian Peninsula, which had an ongoing problem with Bedouins who would steal wooden ties for campfires.[5]

Modern steel ties handle heavy loads, have a proven record of performance in signalized track, and handle adverse track conditions. Of high importance to railroad companies is the fact that steel ties are more economical to install in new construction than creosote-treated wood ties and concrete ties. Steel ties are utilized in nearly all sectors of the worldwide railroad systems including heavy-haul, class 1’s, regional, shortlines, mining, electrified passenger lines (OHLE) and all manner of industries. Notably, steel ties (bearers) have proven themselves over the last few decades to be advantageous in turnouts (switches) and provide the solution to the ever-growing problem of long timber ties for such use.

When insulated to prevent conduction through the ties, steel ties may be used with track circuit based train detection and track integrity systems. Without insulation, steel ties may only be used on lines without block signaling and level crossings or on lines that use other forms of train detection such as axle counters.

Plastic/Rubber Composite

In more recent times, a number of companies are selling composite railroad ties manufactured from recycled plastic resins,[6] and recycled rubber. Manufacturers claim a service life comparable with wooden ties, and that the ties are impervious to rot and insect attack,[7][8][9] and can be modified to provide additional lateral stability[7] while otherwise exhibiting properties similar to their wooden counterparts in terms of damping impact loads and sound absorption. Dimples can be added on the sides and bottom the better to grip the ballast with.

Aside from the environmental benefits of using recycled material, plastic ties usually replace timber ties soaked in creosote, the latter being a toxic chemical,[10] and are themselves recyclable.[7] Plastic/Rubber composite ties are used in other rail applications such as underground mining operations.[11]

In 2009, Network Rail announced that they were to begin replacing wooden ties by recycled plastic ones made by I-Plas ltd of Halifax, Yorkshire;[12] but the I-Plas went into insolvency in October 2012.[13]

The Cable TV series Factory Made has a segment on the manufacture of plastic ties.[14]

In 2012, New Zealand ordered a trial batch of "EcoTrax" brand recycled composite sleepers from Axion for use on turnouts and bridges.[15][16]


Ties may also be made from fiberglass.[17]

Non conventional Tie forms

Y shaped ties

An unusual form of tie is the Y shaped tie, first developed in 1983. Compared to conventional ties the volume of ballast required is reduced due to the load spreading characteristics of the Y-sleeper.[18] Noise levels are high but the resistance to track movement is very good.[19] For curves the three point contact of a Y steel tie means that an exact geometric fit cannot be observed with a fixed attachment point.

The cross section of the ties is an I-beam.[20]

As of 2006 less than 1000 km of Y-tie track had been built of which approximately ninety percent is in Germany.[18]

Twin ties

The ZSX Twin tie is manufacturered by Leonhard Moll Betonwerke GmbH & Co KG and is a pair of two pre-stressed concrete ties longitudinally connected by four steel rods.[21] The design is said to be suitable for track with sharp curves, track subject to temperature stress such as that operated by trains with eddy brakes, bridges and as transition track between traditional track and slab track or bridges.[22]

Wide ties

Concrete monoblock ties have also been produced in a wider form (e.g. 57 cm (22 in)) such that there is no ballast between the ties; this wide tie increases lateral resistance and reduces ballast pressure.[23][24][25] The system has been used in Germany[26] where wide ties have also been used in conjunction with the GETRAC A3 ballastless track systems.[27][28]

Bi-block ties

Bi-block (or twinblock) ties consist of two concrete rail supports joined by a steel bar. Advantages include increased lateral resistance and lower weight than monobloc concrete ties, as well as elimination of damage from torsional forces on the ties center due the more flexible steel connections.[29] This tie type is in common use in France,[30] and are used on the high-speed TGV lines.[31] Bi-block ties are also used in ballastless track systems.[30]

Frame ties

Frame ties (German: Rahmenschwelle) comprise both lateral and longitudinal members in a single monolithic concrete casting.[20] This system is in use in Austria;[20] in the Austrian system the track is fastened at the four corners of the frame, and is also supported midway along the frame. Adjacent frame ties are butted close to each other. Advantages of this system over conventional cross tie ties are reduced ballast pressure (up to half), increased lateral resistance, and increased support of track. In addition, construction methods used for this type of track are similar to those used for conventional track.[32]

Ladder track

Main article: Ladder track

In ladder track the ties are laid parallel to the rails and are several meters long. The structure is similar to Brunel's baulk track; these longitudinal ties can be used with ballast, or with elastomer supports on a solid non-ballasted support.

Fastening rails to railroad ties

Various methods exist for fixing the rail to the railroad tie. Historically spikes gave way to cast iron chairs fixed to the tie, more recently springs (such as Pandrol clips) are used to fix the rail to the tie chair.

Other uses

In recent years, wooden railroad ties have also become popular for gardening and landscaping, both in creating retaining walls and raised-bed gardens, and sometimes for building steps as well. Traditionally, the ties sold for this purpose are decommissioned ties taken from rail lines when replaced with new ties, and their lifespan is often limited due to rot. Some entrepreneurs sell new ties. Due to the presence of wood preservatives such as coal tar, creosote or salts of heavy metals, railroad ties introduce an extra element of soil pollution into gardens and are avoided by many property owners. In the UK, new oak beams of the same size as standard railroad ties, but not treated with dangerous chemicals, are now available specifically for garden construction. They are about twice the price of the recycled product. In some places, railroad ties have been used in the construction of homes, particularly among those with lower incomes, especially near railroad tracks, including railroad employees. They are also used as cribbing for docks and boathouses.

The Spanish artist Agustín Ibarrola has used recycled ties from RENFE in several projects.

In Germany, use of wooden railroad ties as building material (namely in gardens, houses and in all places where regular contact to human skin would be likely, in all areas frequented by children and in all areas associated with the production or handling of food in any way) has been prohibited by law since 1991 because they pose a significant risk to health and environment. From 1991 to 2002, this was regulated by the Teerölverordnung (Carbolineum By-law), and since 2002 has been regulated by the Chemikalien-Verbotsverordnung (Chemicals Prohibition By-law), §1 and Annex, Parts 10 and 17.[33]

Ballastless track

Ballastless track is designed such that no underlying ballast is required. The first such tracks were mountain railways (like Pilatus railway, built in 1889) with rails attached directly to the mountain rock. From the late 1960s onwards, German, British, Swiss and Japanese railroads experimented with alternatives to the traditional railway tie in search of solutions with higher accuracy and longevity, and lowered maintenance costs.[34]

This gave rise to the ballastless railway track, especially in tunnels, high-speed rail lines and on lines with high train frequency, which have high stress imposed on trackage. Paved concrete track[35] has the rail fastened directly to a concrete slab, about half a meter thick,[36] without ties. A similar but less expensive alternative is to accurately position concrete ties and then pour a concrete slab between and around them; this method is called "cast-in precast sleeper track".[37]

These systems offer the advantage of superior stability and almost complete absence of deformation. Ballastless track systems incur significantly lower maintenance costs compared to ballasted track.[36][38] Due to the absence of any ballast, damage by flying ballast is eliminated, something that occurs at speeds in excess of 250 km/h (150 mph). It is also useful for existing railroad tunnels; as slab track is of shallower construction than ballasted track, it may provide the extra overhead clearances necessary for converting a line to overhead electrification, or for the passage of larger trains.[39]

Building a slab track is more expensive than building traditional ballasted track,[38][39] which has slowed its introduction outside of high-speed rail lines. These layouts are not easy to modify after they are installed,[39] and the curing time of the concrete makes it difficult to convert an existing, busy railway line to a ballastless setup.[38]

Slab track can also be significantly louder and cause more vibration than traditional ballasted track. While this is in some part attributable to slab track's decreased sound absorption qualities, a more significant factor is that slab track typically uses softer rail fasteners to provide vertical compliance similar to ballasted track; these can lead to more noise, as they permit the rail to vibrate over a greater length.[36]

Where it is critical to reduce noise and vibration, the concrete slab can be supported upon soft resilient bearings. This configuration, called "floating slab track", is expensive and requires more depth or height,[39] but can reduce noise and vibration by around 80%.[40] Alternatively, the rail can be supported along its length by an elastic material; when combined with a smaller rail section, this can provide a significant noise reduction over traditional ballasted track.[36]

See also



Further reading

External links

  • Y sleepers in Switzerland - rack and normal railways.